History for WinLog 2.0 and MiniLog2 Firmware ================================================================================================ Build 106 (February 2024) - Further improvement to the license system - More information in QM data - Improvement of filters for 1ms data loggings - Option for exporting the timestamp of DCVG/CIPS from MiniLog2 added - Solved * Problem in the display of battery-powered MTP in channel 4 * Error in display when using the mouse zoom * Error in "*.kml" files * Problem with DCVG/CIPS with one point ================================================================================================ Build 105 (March 2023) - Improvement to the license system - Solved * Problem saving special Coupon measurements fixed ================================================================================================ Build 104 (January 2023) - Display of the device type and the serial number in the table - Detection of special Coupon measurements fixed ================================================================================================ Build 103 (November 2022) - Revision of the firmware update for MiniLog2 ================================================================================================ Build 102 (October 2022) - Optimized export to csv files - Export of data loggings to mdt format (Winchart) - Save raw data from MiniLog2 storage ================================================================================================ Build 101 (September 2022) Special version(not released) ================================================================================================ Build 100 (September 2022) Special version(not released) ================================================================================================ Build 099 (August 2022) - Solved * Error from build 097, reading of data loggings stops after 3 minutes measureing time ================================================================================================ Build 098 (August 2022) Special version(not released) ================================================================================================ Build 097 (August 2022) *** New firmware V1.037 for MiniLog2 - Corrected from V1.035: Data logging didn't start for several sampling rates - Corrected from V1.033: Rounding errors with 1ms data logging and ML2 with serial < 2400 - During 1ms data logging the channel 1 value is presented in the display - Automatic calibration of the internal real time quarz when the ML2 is left in standby for 24h, with GPS antenna connected and sufficient GPS signal reception - Lower power consumption when data logging in "MIC" range for sampling times >= 5s - "SYNC ???" warning in the display, if DCVG/CIPS is started without a new GPS synchronisation in the last 24h - Solved: * Format of date/time in Excel adjusted, for CIPS/DCVG export to Excel ================================================================================================ Build 096 (July 2022) - Solved: * Google Maps creation for DCVG/CIPS was faulty ================================================================================================ Build 095 (not released) *** New firmware V1.035 for MiniLog2 - Intermediate version, was not officially released ================================================================================================ Build 094 (April 2022) - 1ms datalogging with dashed lines representing values with overflow in the graphic and 'over' in the table - History file accessible in WinLog 2.0 - Last synchronisation of MiniLog2 shown in 'Identification' - Solved: * Format of Date/Time in Excel * Building *.csv/*.xlsx files of DCVG/CIPS on French Windows * GPS coordinate processing optimized * Format of values in statistics adjusted for high factors ================================================================================================ Build 093 (December 2021) - Solved: * Errors when exporting data loggings to Excel * Problems with GPS coordinates when reading DCVG/CIPS ================================================================================================ Build 092 (June 2021) *** New firmware V1.033 for MiniLog2 - Rare error when saving DCVG/CIPS values, by using the OK key - 1ms loggings show partly wrong values for MiniLog2 with serial < 2400 - Storing GPS coordinates during 100ms loggings for every 2min until the end of logging - Storing GPS coordinates for all loggings after pressing a key and falling back on 2min rhythm, same like after a logging start - Keyboard shortcuts to further improve the MiniLog2 work flow Ctrl+I Identification, Ctrl+L Logging, Ctrl+D DCVG/CIPS, Ctrl+E Excel Export - Excel Export for data loggings improved - Dashed lines represents values with overflow in the graphic - General improvements for the graphic presentation - Helpful presentation of how to start a programmed logging in the programming dialog - The 'About WinLog 2.0' menu presents the sub number of the build version - Last used file directory is saved when leaving - Rounding of values and overflow warnings are improved - Solved: * Missing values for the start and end of measuring gaps in MiniTransPlus loggings, when "Draw through gaps" is active * A missing GPS coordinate in the first line of a DCVG/CIPS measurement leads to ignoring all following GPS coordinates * Crashing after constant/factors have been deleted * Some user settings were not saved on leaving * One line missing in DCVG/CIPS Excel export ================================================================================================ Build 090 (July 2020) *** New firmware V1.030 for MiniLog2 - For Coupon measurement with 1ms delay there's no 20ms median building anymore - POT/DIFF presentation for DCVG/CIPS choosable for the simultaneous presentation of potential ON/OFF and gradient difference - Support of the MiniCoup1K - Excel and CSV export of data loggings contains the QM data in the first row - For MiniTransPlus data loggings, the printing of comments is automatically disabled (can be activated) - For MiniTransPlus data loggings, missing data is automatically traced (can be disabled) - Customizations for data loggings with MiniCoup1K added - Default storage path for files set to the user's documents folder - Custom print format "Waikura" added (for customers in Australia and New Zealand) - Solved: * Measured values out of range are no longer drawn * For erased files, the GPS coordinates are also erased * Loss of axis settings when exiting the print menu * Recalculation for Goolge Maps coordinates (DCVG-/CIPS) * Format for non measured data of MiniTransPlus is like measured data * Option 'Apply settings from graphics' applies comments setting * KML and HTML files are created when the IMD/CSV file contains at least 2 coordinates ================================================================================================ Build 086 - 089 (not released) *** New firmware V1.029 for MiniLog2 - Proper handling for time zones west of Europe - General mistakes for "Over" warnings corrected - "Over" warning now also for Coupon Idc > 10mA or Iac > 20mA ================================================================================================ Build 085 (August 2019) *** New firmware V1.028 for MiniLog2 - Correct date for data logging and CIPS/DCVG when working with old Garmin GPS receivers who got the "GPS Rollover problem" - Lower current consumption when working with GPS during data loggings After each start of a new data logging with a connected GPS receiver, independent from the sampling rate, new coordinates are stored every 2 minutes After the first hour of data logging new coordinates are stored only: every 5 min for 100ms, 0,5s, 1s und 2s every 60 min for 5s, 10s und 30s, every 6 hours for 1min sampling rate - Extended display time for "Point X" after "OK" button is pressed for CIPS/DCVG ================================================================================================ Build 084 (May 2019) - Solved: * Wrong GPS coordinates in printout (country-specific setting) * Wrong date in data loggings and DCVG/CIPS from Garmin GPS rollover problem reading MiniLog2 * Settings from print dialog not completely taken over * Wrong colors in statistics/legend of the print dialog * Too many decimal places for large values [kV/kA] ================================================================================================ Build 083 (December 2018) *** New firmware V1.027 for MiniLog2 - Faultless 1ms logging for MiniLog2 (required only for serials > 2360) - Decreased current consumption with GPS during alarm waiting time - 10 MOhm input impedance for CIPS (before 200 KOhm) - Decreased current consumption for older electronic relay versions - Extension of the threshold list for DCVG/CIPS up to 1000mV - Solved: * Problems with displaying loggings with factors + constants ================================================================================================ Build 082 (April 2018)     - Solved:       * Reading and display errors of MiniLog 128/512 * Reading and display errors of MiniLog2 1ms data loggings ================================================================================================ Build 081 (February 2018)     - Solved:       * Reading and display errors of data loggings ================================================================================================ Build 080 (December 2017) - Adaptation to MiniTransPlus data loggings        - Solved:       * Display of the measured values with delimeter in Excel       * Incorrect formatting of statistics in main window       * Display of the page number for the IntMess Excel export ================================================================================================ Build 079 (August 2017) *** New firmware V1.026 for MiniLog2 - Reduced power consumption with electronic relays - Change from .NET framework 3.5 to .NET framework 4 - Export of DCVG/CIPS measurement to Excel in IntMess 3.0 look with graphics - Optional drawing of missing values (only MiniTransPlus) in graphics and printout - Smaller Google Maps view in printout - Change the start, end, and duration functions in the printout - File name suggestion in the 'Save As' dialog - Solved: * Incomplete Files of DCVG/CIPS measurement with incorrectly formatted GPS coordinates (Trimble) * Problems when reading DCVG/CIPS measurements from MiniLog2 with undefined GPS coordinates * Formatting of values in Excel/CSV * Undefined behaviour of comments in printout * Error with the Google Maps handling in printout * Not executable program when using wrong proxy server settings ================================================================================================ Build 078 (January 2017) *** New firmware V1.025 for MiniLog2 - GPS: Correct handling of new leap second (introduced January 2017), to work even without a learning cycle for GPS antenna - Solved: * Crash when exporting *.imd files to Google Maps without coordinates * Missing Google Maps files when reading DCVG/CIPS from MiniLog2 ================================================================================================ Build 077 (December 2016) *** New firmware V1.024 for MiniLog2 - Solved * DCVG: Wrong gradient difference of 0 mV when OFF cycle is shorter than 1s (Error only in V1.022) * DCVG: Values frozen in display (Error only in V1.023) - Detection of language for installed version of MS Excel - Changed format in Excel and CSV file when exporting data loggings ================================================================================================ Build 076 (October 2016) - Wrong Timestamp from MiniLog2 identification will be ignored and set to 00:00:00 - Solved: * Error when applying settings from graphics in the print menu * Internet communication problems (update and Google Maps) ================================================================================================ Build 075 (June 2016) *** New firmware V1.022 for MiniLog2 - GPS: Correct handling of new leap second (introduced July 2015), to work even without a learning cycle for GPS antenna - Solved * External OK button for DCVG not always functioning * High AC values (> 40V) measured too inacurrate * Mechanical relay opened during night saving - Excel/CSV export reworked - Adaption to data loggings of MiniTransPlus ================================================================================================ Build 074 (January 2016) - Format of values in Excel export / csv files customized - Solved: * Saving colour of channels was incorrect * Excel warning for long running tasks blocked the export ================================================================================================ Build 073 (October 2015) - Solved: * Missing representation of seconds in the printout ================================================================================================ Build 072 (October 2015) - Solved: * Wrong country-specific formatting for Excel Export * Errors in the presentation of comments in the printout * Errors in the printout combined with Google Maps * Incorrect formatting of the unit in the threshold statistics * Missing takeover of selected 'Off-Mean Value' from the screen to the printout * Error in setting the unit for 1ms samplings * Errors in the presentation of the statistics * Error when exporting a DCVG / CIPS measurement to Excel (IntMess form) without GPS coordinates ================================================================================================ Build 071 (April 2015) - In 1ms data loggings the sampling rate can be reduced to e.g. 100ms afterwards - Solved: * Abort during transfer of DCVG / CIPS measurements with more than 1920 points * Incorrect label oft the left y-axis for print out when activating the right y-axis * No programming of the start time for a data logging with 1ms sampling rate, when an end time is selected ================================================================================================ Build 070 (April 2015) - Solved: * Crash when printing data loggings with GPS coordinates * Missing 4th comment line in print out after applying the setting from graphic * Error in the detection of '.' and ',' as decimal separator * Crash when drawing/printing with extreme zoom levels * Very slow Excel export of data loggings ================================================================================================ Build 069 (February 2015) *** New firmware V1.020 for MiniLog2 - MiniCoup: Waiting times 1ms and 2ms added (previously 5, 10, 20, 50, 100 and 200 ms) for the measurement start after disconnecting the coupon - MiniCoup: When using "Alarm" mode (programmed start of data logging) the MiniCoup relay stays now closed until the data logging starts so that the coupon receives voltage from the pipeline. - MiniCoup: After each sampling (every second) the switch off time is shifted by 1 ms to make possible 50/100Hz influence on the OFF potential of the coupon more visible. After 20s (= 20ms shift) the switch off time is moved back 20ms to the beginning and the shift starts again. - Remote control of the MiniLog2 by external contact on the feature connector ("Feat.") for installation as a GPS switcher on remote control systems With the feature contact open, the MiniLog2 switches as programmed. With the feature contact closed, MiniLog2 stops switching. As accessory, a "Control Cable for the Feature Connector" with two open ends is available - Solved: Sometimes no USB data transfer when the battery was not fully charged - New "average" for 1ms data loggings under the principle of a low-pass filter - "Print chart from screen" is omitted and was replaced by possible takeover of parameters directly from the screen graphics in the print menu - Print settings are saved by selecting "Apply" or "OK" when editing the print menu - Printer selection will appear in front of each print out The selection of the printer is now in front of each printout and has not to be set in advance - Extended dialog under "Extras" -> "Options" - Conversion of the "Google Maps" exports from *.kml to *.html, as Google Maps does not accept *.kml files after February 2015 - Solved: * Crash when manually selecting channel 2, 3 or 4 for 1ms data loggings * Missing last measured point in *.imd files ================================================================================================ Build 068 (October 2014) - Printout with relative X-axis label selectable Optionally the X-axis labels start at 00:00 clock and show only the time difference since the start of recording - New format of the statistic for the Excel export of data loggings - Extended programmed recording for Coupon measuring New delays (1, 2, 5, 10, 20, 50, 100 and 200 ms) for the start of the measurement after disconnecting the coupon - Google Maps for DCVG/CIPS optimized Upon exceeding the threshhold not only the gradients but also possible measured potentials are displayed - Solved: * Missing drawing of the moving average in printout * Too small units by large factor in screen and print graphics * Crash when double-clicking on data logging files * Pasting comments from the clipboard into the table leads to a possible crash when loading the data logging file * Incorrect centering of the screen graphic after loading a data logging * Statistics of Excel export calculates the standard deviation only from the screen image, instead from the total logging * Off mean values for screen printout cannot be deselected * Crash after changing the factor / offset / unit settings for 1ms registrations * Date / time in Excel export of IMD files shows 01/01/2001 00:00 clock * Slow Google Maps upload ================================================================================================ Build 067 (May 2014) - Faster Excel export of data loggings - Expanded scope of the Y-axis in the graph, new maximum scale ±10kV (resp.kA) - Units extended to kV and kA in print out - Google Maps communication possible when the networks uses a proxy server to access the internet In the menu "Extras" -> "Options" the IP adress and port of the proxy server as well as the user name and password have to be entered - Solved: * Crash when uploading IMD files to Google Maps * Error in table values for values > 1kV * Possible wrong coordinates for info pin in Google Maps ================================================================================================ Build 066 (March 2014) - Changed unit format for graphic printout - Statistics of data loggings for Excel exports (*.xlsx) - Solved: * Negative AC current in MiniCoup data loggings * Missing decimal separator for Excel exports * Incorrect translations * Incorrect display of the moving average values of 1ms data loggings after "File Open" ================================================================================================ Build 065 (January 2014) - Constants with 0.1 µV resolution - Gradients for DCVG / CIPS measurement with 0.1 mV resolution - Optimized marking of x-axis for 1ms samplings - Solved: * Possible crash after input of comments * Excel export partially blocked under Win XP and earlier Office versions * Bad formated mV value for 1-channel MiniLog 128/512 files * Y axis doesn't show optimal scale after data transfer and file opening * Duplicate query when saving DCVG / CIPS measurements * Progress bar not visible during data transfer * .log, .asc and .wl2 files in foreign format lead to a crash * DCVG / CIPS distances when calculated in Yard show useless decimals ================================================================================================ Build 064 (October 2013) - Solved: * Firmware update not possible for MiniLog2 from V1.012 to V1.018 or higher * Wrong time format in graphic screen for Latin and South America ================================================================================================ Build 063 (September 2013) *** New firmware V1.019 for MiniLog2 - The GPS receiver Trimble GeoXH 6000 (with down to 10cm accuracy) can be used with MiniLog2 with a special cable adapter. Only coordinates storing is possible, but no GPS synchronisation. - Switching times > 1 min programmable With the menu (SWITCH -> CYCLE: "CYCLE PRO") ON and OFF times up to 60min can be selected in 1min steps. - Invert switching programmable With the menu (SWITCH -> CYCLE: "CYCLE PRO") and after confirming the ON and OFF cycle the user can select the relay to work inverted. This assures the compatibility with switchers starting with the ON and not with the OFF time on second 0. - Sleep times programmable With the menu (SWITCH -> SLEEP: "YES") the start and end time of the sleeping period can be setup. - "OVER" warning during CIPS/DCVG measurement for potentials more negativ than -9.0V and more positiv than +1.5V and for gradients more negativ than -3.0V and more positiv than +3.0V. - CIPS potential measurement with filters down to 0.4s OFF cycle. Shorter cycles than 0.4s allow gradients to be measured only. - Solved: Wrong display of charging current when reading the identification with WinLog 2.0 - Data logging and DCVG files contain the WinLog 2.0 build version of the data transfer - DCVG files have a unified number of digits - Google Maps files are only saved when the DCVG measurement contains GPS coordinates - Solved: * Text of labels corrected when comparing files (translation) * Precise error handling when exporting to Excel * Overshoot for data loggings with 100ms sampling * Rare error (message: "Unexpected end of line. Datatransfer stopped.") corrected when reading the data logging * Rare crashes when right Y-axis is enabled (printout) ================================================================================================ Build 062 (July 2013) - New menue item "Change Sampling rate" In preparation for the comparison of data loggings this new menu item allows adapting of the sampling rate for a data logging (not for 1ms and not for coupon data loggings) - New menue item "Compare" Allows the comparision of two data loggings with maximum of 2x DC and 2x AC (not for 1ms and not for coupon data loggings) - Copy / paste of text in the table with keyboard - Improved naming for the creation of DCVG files (eg. DCVG(1-3).imd, DCVG(2-3).imd, etc.) - Optimized checking if internet is available for updates/Google Maps - Solved: * Wrong display of standard deviation for negative factors * Wrong display of "Over" for 1ms data loggings in combination with filters and factors/offsets ================================================================================================ Build 061 (May 2013) - "CSV" format for Excel export of data loggings selectable - "CSV" format for Excel export of DCVG measurements - Solved: * Limit value in the printout with missing digits * Crash with incomplete data logging files * Crash during Excel export ================================================================================================ Build 060 (May 2013) - Faster drawing of the printout - Statistic on screen shows a tooltip with date/time of minima and maxima and mouse click sets the cursor in graphic and table accordingly - When exporting DCVG measurement to Google Maps, the limit value and the file name are stored beside the data - When exporting DCVG measurements to Excel, the limit value is stored beside the data and values out of limit are marked in red - Automatic creation of *.csv files for the Excel export, if no installed Excel is found - Zoom of the X-axis is performed in the middle, not as previously at the beginning - Solved: * Wrong "Over" warning for measurements with MiniLog 128/512 * Problems when opening old data logging files with manual GPS coordinates missing * Incorrect calculation of the standard deviation ================================================================================================ Build 059 (March 2013) - Solved: * New Google Maps connection in print menu (former version was deactivated by Google) ================================================================================================ Build 058 (January 2013) *** New firmware V1.018 for MiniLog2 - 7 times faster USB transfer of samplings (old version 5:20 min new only 0:50 min) - Error at "Coupon" samplings of V1.017 solved * After 1.5h (=64 kbyte) wrong measurements were stored, because the FLASH memory was not cleared correctly - Correct saving of battery level when sampling "1ms" and "Coupon" - Faster drawing of graphics on the screen - Exceeded measuring ranges are marked as "Over" in sreen and Excel tables - Solved: * Endtime was sometimes handled incorrect during printing * Google Maps disabling when printing has been incorrectly stored in the file ================================================================================================ Build 057 (December 2012) - Solved: * Error while saving AC1 measurements from MiniLog 128/512 * Wrong selection of GPS coordinates in print preview * Problems with moving average for 1ms samplings ================================================================================================ Build 056 (December 2012) *** New firmware V1.017 for MiniLog2 - Sampling with GPS coordinates * If a GPS antenna is connected, the GPS coordinates are automatically stored beside every minute (only for sampling rate 100ms, 500ms, 1s and 2s). Later with the WinLog 2.0 print out a Google Maps picture can be added showing the location in regards to the sampling time. By this, locations and its corresponding sampling values are easily assigned together, even if many successive samplings without stopping the MiniLog2 logging have been made. - Improved DCVG and CIPS measurement * Better AC damping, especially for 16,6 Hz * For shorter off cycles (< 0.5s) the measurement length is reduced down to 100ms minimum, for better results under stray current * Improved and more stable gradient measurement by switching to microvolt resolution if below 100 mV * Display and keyboard light stays on for night measurements (05pm till 08am) - Solved: * Problems with the GPS leap second * Programming of end time for 1ms samplings * 30 min duration for 1ms samplings also for MiniLog2 with serial < 120 - Handling of GPS coordinates during a sampling - Calculation of the moving average for 1ms samplings - Off-Mean value calculation extended to enter an endtime manually - 1ms samplings can be programmed with an active alarm end time - Y-axis in graphic extended with 10, 20 and 50µV scope (limited scrolling) - Limit values of potential measurements for DCVG changed - Solved: * Language settings for Excel export of DCVG measurements * AC/DC recognition for old *.log files * DCVG chainage of large differences between waypoints * Error in detection of right Y-axxis (active/not active) * Wrong settings of filters of 1ms sampling files ================================================================================================ Build 055 - not delivered test version ================================================================================================ Build 054 (September 2012) - New language added: Polish - optimized format of statistics in printout - Solved * Problems during saving the print settings * Google Maps view with wrong language * Problems with "Erase Section" * Flickering of cursor values * High CPU usage when moving the cursor ================================================================================================ Build 053 (August 2012) *** New firmware V1.016 for MiniLog2 - GPS leap (introduced on 1st of July 2012) is properly recognized - Recording mode with alarm also for 1ms and Coupon added - Recording mode with end date/time enabled - Solved: * partly unintended open contact for mechanical relay, if night saving (SLEEP) was activated - Software filters for 1ms samplings With three buttons (16.6Hz, 50Hz and 100Hz) frequencies can be eliminated later. - "Save As" dialog for Windows XP optimized - End time for programmed samplings added When programming a sampling an end time can be set in addition to the start time. -Solved: * Crash when calling the print menu after reading of MiniLog 128/512 samplings * Problems when printing the moving average * Crash "Memory overflow" when opening a file * Factor and offset are correctly taken into account for overrange situations * Problems with faulty Google Maps representation with foreign operating systems ================================================================================================ Build 052 (July 2012) - Not official released ================================================================================================ Build 051 (May 2012) *** New firmware V1.015 for MiniLog2 - Recording Mode with channel selection and alarm time activated - Multimeter and data logging with LogPlot 2.0 (Build 010) for presenting the actual values directly on PC screen www.weilekes.de/download/files/logplot20_en.zip - Displayed channels can be changed during the data logging with the button "Arrow Up" - Improved calculating of battery capacity, especially during long periods with no charging - "SAMP" LCD symbol only flashes for data logging, but no longer for multimeter - Solved: * sometimes too high power consumption after GPS reception and after disconnecting from PC * sometimes no GPS synchronization with Garmin antennas possible * flashing DCVG values when working with fast switching times - Menu "Programming" -> "MiniLog2" -> "Recording Mode" activated (e.g. to deactivate channels or set an alarm time) - DCVG measurements (*.imd) will be exported to MS Excel when Google Maps upload is selected (Menu "Extras" -> "Options" -> "Automatic export to Excel") - Overvoltages are marked in red in the values table - More values selectable for the gradients error threshold (Menu "Extras" -> "Options" -> "Defect threshold gradients difference") - Statistics in printout are activated by default (Menu "File" -> "Pageview" -> "Statistics" -> "Statistics" selected) - Solved: * Errors in statistics for Off-Mean value in printout * Partly missing date values in printout * Lost print settings when saving/loading a file * Problems with black/white pdf printout ================================================================================================ Build 050 (April 2012) - New licence information for update service added ================================================================================================ Build 049 (March 2012) *** New firmware V1.014 for MiniLog2 - Internal flash is now protected against random erases forced by low battery With a low battery the internal calibration of the MiniLog could be erased, this leads to continously wrong measurements because of lost calibration data. - 5 ms time delay added for coupon measurement - After a warmstart, most important settings are left unchanged - The PC Symbol flashes correctly with a USB connection -Timeline in graphic extended, 3 and 4 days are selectable -Standard deviation for "Off-Mean value" is calculated and shown in graphics and printout -In a printout with "Off-mean value" the changed statistic is named -Adjustment for the bootloader for the new firmware V.1014 -The sampling rate is shown in the printout -Reference for the expiration of the update service with a message and display of the date of expiration -Solved: *errors in the naming of the right Y-axis *false message to save the file due to changes in the print dialog which wasn't changed *wrong message for Excel-Export =============================================================================================== Build 048 -Threshold statistic in printout The percentage of below and above threshold for each channel is printed -Off-Mean value selectable period 24h added -Solved: -Excel- and Google Maps-Export of GPS coordinates (only English Windows) -optimized handling of file extension (*.WL2) -errors in print routine -translations added ================================================================================================ Build 047 -New MiniLog2 firmware 1.013: - 1ms sampling rate enabled. 1 kHz single channel sampling for 30 minutes maximum. Note: No display of values during sampling possible, as the sampling takes all the available processing power. - Coupon measurement with 1s enabled. Allows measuring of ON- and OFF-Potential, and DC and AC current for every second. Measurement can be done with "MiniCoup" adapter, or with an external shunt wiring. Preset of the measuring time after the switching available via key (PROG) for 10ms, 20ms, 50ms, 100ms oder 200ms. Display shows potential (On/Off) or current (DC/AC), this is changeable during sampling by key arrow "UP". - (DCVG) measurements without connected GPS antenna possible. Choose with key (MODE) "GPS On/Off" before (START). - (DCVG) during night hours with automatic activation of keyboard and display illumination. - During data logging illumination of display and keyboard via key press possible. - After warm start the (LOGGER) settings are no longer destroyed. - Night- and weekend savings (SLEEP) during active sampling corrected. - Display can be switched off with key (STOP), activation of the display by simple key press. - Communication problems even with PC-Symbol corrected -User defined limit line is not printed when value is zero -Samplings with 1ms activated -Excel-Export (Office 2007,2010) for samplings with 1ms is limited to 1 million values -Coupon sampling activated -Solved: -Problems with comments containing ";" -Problems with y-axis in printdialog -Errors with positions for Google Maps Build 046 - DCVG without GPS gets index as meter IMD-files contain the date of first value taken Solved: -possible problems with distance calculation in *.kml files -problems with showing the units -problems with the printout with Adobe PDF -problems with the logo -problems with printimng of "Off-Mean value" -Format of AC-values in the table corrected Build 045 - New firmware 1.012 for MiniLog2 to solve update problems in 1.011 Color definition in *.WL2 files are supported Activated "Off-Mean-Values" can be printout via "Print chart from screen" Build 044 - Bugfix Build 043 - User defined limit line in graphic printout New firmware 1.011 for MiniLog2 to solve keyboard problems Solved: -possible crashes when using moving average -problems with logo in quick print Build 042 - New Y-Axis assignment of the channels in printout For more than two channels and an active right y-axis the DC channels are assigned to the left side and the AC channels to the right Support for MiniCoup Correction of the min/max lines in the printout Changed formats in statistics DCVG: -support for Omnistar GPS antennas -reading of DCVG samplings with broken MiniLog2 identification possible Build 041 - Solved: -Communicationproblem during reading of Identification from MiniLog2 -Error in GPS-coordinates in Asia Improved accuracy/rounding when printing right y-axis Improved visualisation of marks (min, max, median) in printout Build 040 - Solved: -Error from Build 039: Programming the Identification is accessible again Build 039 - Mousezoom optimized Rework: -Communication with MiniLog2 Build 038 - Add new language: Romanian Solved: -possible wrong showing of memory use of samplings -problems reading MiniTrans datalogging Build 037 - Solved: -use of markers in table for "Erase section" -problems Google Maps export -problems reading DCVG -problems reading *.log files Build 036 - New firmware V1.009 for MiniLog2 - External button for the "FeatureConnector" simulates "OK" button press for DCVG - Fixed some minor errors Changed defect threshold evaluation Context menu (right mousebutton) added for "Erase marker" and zoom out functions Build 035 - Set minimum size for mousezoom Edit: -Google Maps support for printout Solved: -Errormessage when printing after reading of MiniLog Build 034 - Solved:-Error message when starting print setup -"Save as" dialog error -Excel-Export problems on foreign operating systems Build 033 - Reading DCVG from a MiniLog2 or IMD-files creates in addition Excel-files DCVG Excel export can be disabled Automatic upload of DCVG to Google Maps can be disabled Correctoin of GPS reading Solved: -Phantom lines in graphic -Offset and factor reading of old *.log files -statistic settings Build 032 - Programming the MiniLog 128/512 recording settings corrected for AC/AC and sampling rate Printpreview optimized for samplings > 7 days Zoom for X-Axis is up to 10ms Samplingrates with less 100ms are evaluable 120dpi scale for monitorfonts shows right proportion Samplings from start / to end can be deleted Build 031 - Sometimes the progressbar is not shown when reading MiniLog 128/512 samplings, error is fixed Build 030 - New firmware V1.007 for MiniLog2 - Protection against deep discharge during sampling - 4 times higher resolution for Range 'Lo' - optimized communication with WinLog 2.0 Automatic check for firmware update for MiniLog2 Detection of missing printer installation Check for compatibility between MiniLog2 firmware <=> WinLog 2.0 Build version Display state of charge at the end of a sampling Marking when battery was deep discharged during sampling Build 029 - QM-Data reformatted Print - statistic values are rounded more exactly - Date and timeformat changed Build 028 - Excel-Export in Toolbar activated Fileformat changed to manage deaktivated channels Dateformat changed i file Printsettings changed (Time and right Y-Axis) Error in median for right Y-axis solved Identification reading error MiniLog2 fixed Build 027 - Bugfix Build 026 - Correction for creating PDF-documents Error reading WinLog 1.3 files fixed Build 025 - Changes/Bugfix in printmenu Bugfix for saving files Build 024 - Corrected dataformat for CIPS/Gradient measurement Build 023 - Setup changed - Userfolder won't be created Printerrors solved (Time and Y-axis loading from file) Icons Build 022 - Updatecheck errors solved Region settings optimized Build 021 - New driver for MiniLog2 Build 020 - Upload of KML and download of updates via http Format of statisticvalues same as grid Surveilance monitor for MiniLog2 USB communication Build 019 - MiniLog2 reading of dataloggings aktivated Userinterfaces optimized Off-Mean Value-Function activated Format of values changed Bugfixes in printmenu Bugfixes Build 018 - Update improved Bugfixes Build 017 - DCVG-Measuring optimizied direct upload to Google Maps Upload of *.imd- und *.kml-files clock, battery und identification read and write for MiniLog2 check for updates for WinLog2 at programstart Update for MiniLog2 Firmware optimizied bugfix in *.WL2 timeformat Build 015 - New fileformat *.WL2 Build 011 - Implementation of loading DCVG measurements from ML2 creating *.kml-files for GoogleMaps/Earth Build 010 - Printpreview changes µV-Units Comments Commandelements changed Build 009 - Bugfixes Build 008 - Acceleration of printprocess Build 007 - Check for Updates Bugfixes(Mauszoom, Printdialog) Build 006 - MiniLog2 Connection Bugfixes Build 005 - Check for Updates Printdialog Bugfixes Build 004 - New setup Bugfixes Build 003 - Bugfixes Build 002 - Bugfixes Build 001 - First release